This is where you will plug in the antenna removed from the factory radio. AM/FM Antenna: When looking at the back of your Sounstream head unit, your AM/FM connection is the second plug to the right of the main wire harness connection.Allow the connection between your phone and your new Soundstream head unit via your cell phone prompt by selecting "yes".Īdditional Soundstream Installation Tips: Connect your phone to the USB in your glove box. Find a local radio station with a strong signal and test the volume controls on your handlebar controls.Allow the head unit to power up for 1 to 2 minutes before switching to the AM/FM radio source.The first screen shown will be the home screen.Step 2: Soundstream Reserve Head Unit InitializationĪfter making all the connections noted in Step 1, turn your ignition switch to accessory power. This kit is not compatible with bluetooth headsets or Sirius/XM.The hand control module will be connected to the harness for you.Don't be alarmed if you have plugs that were removed from the factory radio and not reused with our bundle.Īdditional Soundstream Reserve Head Unit Notes: In addition, all the plugs connected to your vehicle will not be reused.Double check that all connections made to this point are fully connected. All you're doing is matching plugs - it may look like a lot of wiring but it's simple. All of the plugs in our wiring harness are keyed plugs, which means they will only fit their match on the Harley-Davidson wiring connector/plug side.Install your new Soudstream head unit kit and make all the wiring harness connections: the main harness connection to your Harley-Davidson factory harness connection, AM/FM antenna connection, USB connection and the provided Soundstream microphone connection if you desire to use voice commands or talk on the phone. These items will be preassembled for you when your kit arrives at your door.įollow the disassembly process in the video above to remove your factory Harley-Davidson radio. The Body: This consists of the Soundstream head unit chassis, wiring harness and hand control module (if selected at checkout). Step 1: Installing your Soundstream head unit: NOTE: Road Glide riders, please refer to page 23 of the instruction manual for disassembly and installation instructions. These tips are intended to be used in conjunction with our full installation video below: Step 4: Follow firmware update instruction guide to ensure your system is updated correctly. Step 3: Erase the 3/25/22 firmware update from your thumb drive and then download second firmware update (05/24/22) to your thumb drive *gives maps the ability to go into dark mode in the evening/night* Step 2: Follow firmware update instruction guide to ensure your system is updated correctly. Step 1: Download firmware update (03/25/22) *full software update* to a thumb drive as per the instructions in Step 2. If you're head unit doesn't have the 3/25/22 firmware update, you must complete the 03/25/22 firmware update first, then the 05/24/22 update! Please make sure the thumb drive you're using only has the firmware update file on it and no other files. We update all firmware prior to shipping. NOTE: If you purchase your Soundstream radio from us, you will not need to update your firmware. Connecting these voice coils in parallel will result in a 2Q nominal impedance, which is not recommended for use with bridged channels of your amplifier.Please follow these installation tips when you're ready to install your new Soundstream Reserve HDHU.14 head unit in your 2014+ Harley-Davidson® Touring Motorcycle. Some subwoofer models feature a dual 4Q voice coil design. Connecting two such speakers in parallel will result in a 2Q impedance load as seen by the amplifier. Most speakers designed for car audio operation are 4Q impedance. Continuing to operate the amplifier under these conditions is not recommended and will reduce its life expectancy. When the chassis cools down, normal operation will resume. Although operation with lower impedances is not likely to cause immediate damage to the internal circuitry, the unit will most likely overheat, causing the thermal protection circuitry to shut down the amplifier. When a channel-pair is bridged, the recommended minimum load impedance is 3Q for subwoofer use, and 4Q for full range operation. Your dealer is a valuable resource in helping you with your system design and installation.Įach channel of your amplifier can easily drive 4Q speaker loads when used in the stereo mode. Your authorized dealer has been trained to maximize your system’s sonic potential. By planning your installation carefully you can avoid situations where the performance of the reliability of your system is compromised. Proper system planning is the best way to maximize your amplifier performance.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |